Cracked Canopy Repair
Moderators: Rick, Lance Murray
- SavageB
- 2 Diamonds Member
- Posts: 20
- Joined: Tue Nov 13, 2018 10:35 pm
- First Name: Brian
- Aircraft Type: DA42-VI
- Aircraft Registration: N649DA
- Airports: 50F
- Been thanked: 6 times
Cracked Canopy Repair
According to the manual, you can repair cracks up to 6". However, I can't seem to find someone that does this work.
I pushed too hard on my new bird and cracked the canopy on the pilot side. It's 2.75" long.
2018 DA42-VI
Any thoughts?
I pushed too hard on my new bird and cracked the canopy on the pilot side. It's 2.75" long.
2018 DA42-VI
Any thoughts?
- Don
- 4 Diamonds Member
- Posts: 377
- Joined: Tue Jul 06, 2010 9:15 pm
- First Name: Don
- Aircraft Type: DA40
- Aircraft Registration: N623DS
- Airports: KTOA
- Has thanked: 123 times
- Been thanked: 162 times
Re: Cracked Canopy Repair
Brian, the first thing you have to do is drill a 3/16" relief hole right above the crack so the crack will not continue to travel.
Also, can you elaborate where and how you pushed too hard to crack the canopy so others don't do the same.
Also, can you elaborate where and how you pushed too hard to crack the canopy so others don't do the same.
Last edited by Don on Fri May 10, 2019 5:08 pm, edited 1 time in total.
Diamond Star XLS, N623DS, SN40.1076
- SavageB
- 2 Diamonds Member
- Posts: 20
- Joined: Tue Nov 13, 2018 10:35 pm
- First Name: Brian
- Aircraft Type: DA42-VI
- Aircraft Registration: N649DA
- Airports: 50F
- Been thanked: 6 times
Re: Cracked Canopy Repair
Thanks Don. I have the instructions. The problem is I can't seem to find anyone who will repair it.
It has not moved since I cracked it. According to the repair guide (diamond), they now want a 3/32 hole. Everybody else says 3/16
Thanks!
It has not moved since I cracked it. According to the repair guide (diamond), they now want a 3/32 hole. Everybody else says 3/16
Thanks!
- Don
- 4 Diamonds Member
- Posts: 377
- Joined: Tue Jul 06, 2010 9:15 pm
- First Name: Don
- Aircraft Type: DA40
- Aircraft Registration: N623DS
- Airports: KTOA
- Has thanked: 123 times
- Been thanked: 162 times
Re: Cracked Canopy Repair
My company works a lot with acrylic for large flight simulation rear projection screens. Believe me, it will travel from the vibration of the engines and when you taxi. 3/16" of a hole is standard practice for this type of crack.
Diamond Star XLS, N623DS, SN40.1076
- Colin
- 5 Diamonds Member
- Posts: 2006
- Joined: Sat Aug 21, 2010 8:37 pm
- First Name: Colin
- Aircraft Type: DA42
- Aircraft Registration: N972RD
- Airports: KFHR
- Has thanked: 319 times
- Been thanked: 527 times
Re: Cracked Canopy Repair
The canopy is over five thousand dollars. If it were my plane, I'd not spin the engines until I had done Don's suggestion.
Colin Summers, PP Multi-Engine IFR, ~3,000hrs
colin@mightycheese.com * send email rather than PM
http://www.flyingsummers.com
N972RD DA42 G1000 2.0 s/n 42.AC100 (sold!)
N971RD DA40 G1000 s/n 40.508 (traded)
colin@mightycheese.com * send email rather than PM
http://www.flyingsummers.com
N972RD DA42 G1000 2.0 s/n 42.AC100 (sold!)
N971RD DA40 G1000 s/n 40.508 (traded)
- Steve
- 5 Diamonds Member
- Posts: 1973
- Joined: Thu Aug 12, 2010 1:23 am
- First Name: Steve
- Aircraft Type: DA40
- Aircraft Registration: N432SC
- Airports: 1T7
- Has thanked: 85 times
- Been thanked: 503 times
Re: Cracked Canopy Repair
There seems to be some diversity of opinion as to what size bit should be used to stop drill acrylic sheet. Anywhere from 3/32" (Diamond) to 3/16" (Don). Probably means that anywhere in that range would be OK. I would tend toward the lower end of the range, or maybe compromise on 1/8".
I have done a fair amount of work assembling acrylic structures (for the lab and display cases for my Dad's ship models). If that were my canopy, I would (along with my IA) stop drill (1/8"), glue the crack with some thin Weldon 4 adhesive (it is extremely low viscosity and will wick into the crack. Use a very small amount (they make applicators for this purpose), applied from each end of the crack, and allow it to cure. I would also run a small amount under the edge of the vent latch "socket", since the crack runs under that piece, and the rear edge appears to have disbonded slightly. If you get adhesive on the canopy surface, you can polish it off after it cures. Lastly, fill the stop drilled hole with clear silicone. Here are a few online references which you may find useful:
http://www.eaavideo.org/detail/video/4922730282001
http://www.plasticgenius.com/2009/03/re ... glass.html
Like Don and Colin, I would refrain from operating the aircraft until you make the repair (or at least stop drill the crack). Good luck,
Steve
I have done a fair amount of work assembling acrylic structures (for the lab and display cases for my Dad's ship models). If that were my canopy, I would (along with my IA) stop drill (1/8"), glue the crack with some thin Weldon 4 adhesive (it is extremely low viscosity and will wick into the crack. Use a very small amount (they make applicators for this purpose), applied from each end of the crack, and allow it to cure. I would also run a small amount under the edge of the vent latch "socket", since the crack runs under that piece, and the rear edge appears to have disbonded slightly. If you get adhesive on the canopy surface, you can polish it off after it cures. Lastly, fill the stop drilled hole with clear silicone. Here are a few online references which you may find useful:
http://www.eaavideo.org/detail/video/4922730282001
http://www.plasticgenius.com/2009/03/re ... glass.html
Like Don and Colin, I would refrain from operating the aircraft until you make the repair (or at least stop drill the crack). Good luck,
Steve
- Don
- 4 Diamonds Member
- Posts: 377
- Joined: Tue Jul 06, 2010 9:15 pm
- First Name: Don
- Aircraft Type: DA40
- Aircraft Registration: N623DS
- Airports: KTOA
- Has thanked: 123 times
- Been thanked: 162 times
Re: Cracked Canopy Repair
Quite frankly if, it was my 2018 plane, I would be calling my insurance company for a new replacement canopy. Even if you structurally repair it properly so that the crack will not continue to creep, the repair will still be visible and cosmetically detract from the appearance of the aircraft. That said, my friends say I am anal about keeping all my toys and stuff looking like new so it may not bother others as much as it would myself. Just sayin.
Diamond Star XLS, N623DS, SN40.1076
- Colin
- 5 Diamonds Member
- Posts: 2006
- Joined: Sat Aug 21, 2010 8:37 pm
- First Name: Colin
- Aircraft Type: DA42
- Aircraft Registration: N972RD
- Airports: KFHR
- Has thanked: 319 times
- Been thanked: 527 times
Re: Cracked Canopy Repair
I have now learned that Don is one of the few people I would be happy partnering with for an airplane. I hate when things start to look bedraggled.
Colin Summers, PP Multi-Engine IFR, ~3,000hrs
colin@mightycheese.com * send email rather than PM
http://www.flyingsummers.com
N972RD DA42 G1000 2.0 s/n 42.AC100 (sold!)
N971RD DA40 G1000 s/n 40.508 (traded)
colin@mightycheese.com * send email rather than PM
http://www.flyingsummers.com
N972RD DA42 G1000 2.0 s/n 42.AC100 (sold!)
N971RD DA40 G1000 s/n 40.508 (traded)
- Steve
- 5 Diamonds Member
- Posts: 1973
- Joined: Thu Aug 12, 2010 1:23 am
- First Name: Steve
- Aircraft Type: DA40
- Aircraft Registration: N432SC
- Airports: 1T7
- Has thanked: 85 times
- Been thanked: 503 times
- Lance Murray
- 5 Diamonds Member
- Posts: 1163
- Joined: Tue Jul 06, 2010 11:25 pm
- First Name: Lance
- Aircraft Type: DA40
- Airports:
- Has thanked: 7 times
- Been thanked: 120 times
Re: Cracked Canopy Repair
Definitely stop drill the crack before operating. If you are in So Cal I have a guy that may repair It but no one will guarantee the repair or results. PM me and I can forward the name. But as Don noted above I would report this to the insurance company.
Remember that acrylic drill bits are different. Don't use a standard drill bit. It can chatter and make the problem worse. Acrylic bits are sharper at the tip.
Remember that acrylic drill bits are different. Don't use a standard drill bit. It can chatter and make the problem worse. Acrylic bits are sharper at the tip.