Torque for the oil temp probe

Any DA40 related topics

Moderators: Rick, Lance Murray

Post Reply
User avatar
astaib
5 Diamonds Member
5 Diamonds Member
Posts: 616
Joined: Mon Feb 26, 2018 9:00 pm
First Name: Arnaud
Aircraft Type: DA40
Aircraft Registration: FGNJX
Airports: LFPX
Has thanked: 244 times
Been thanked: 51 times

Torque for the oil temp probe

Post by astaib »

Hello,

Do you know what is the torque for the oil temperature probe?
I didn't find it in the AMM.

Thank you very much.

Arnaud.
Arnaud
DA40 Star 180 / 40.026 / 2001
Wingtip, landing and taxing LED (Whelen)
Skitube
GNS430 NON-WAAS
Steam gauges
Non certified ADS-b
User avatar
Lance Murray
5 Diamonds Member
5 Diamonds Member
Posts: 1163
Joined: Tue Jul 06, 2010 11:25 pm
First Name: Lance
Aircraft Type: DA40
Airports:
Has thanked: 7 times
Been thanked: 118 times

Re: Torque for the oil temp probe

Post by Lance Murray »

"As a general rule, pipe fittings with tapered threads should not be assembled to a specific torque because the torque required for a reliable joint varies with thread quality, port and fitting materials, sealant used, and other factors"  
*Parker Hannifin Catalog 4300 Port End Assembly, page T7



Leakage path through NPT threads shown at red points. No matter how tight you make NPT threads, a leakage path still exists. It is the function of the sealant to block the path between the male and female thread.

There is no standardized method of tightening an NPT fitting (tapered pipe fitting). Your best bet is to follow the standards for your industry. What follows is a rather lengthy discussion of problems you might encounter using all of the commonly used methods. This will help keep you out of trouble when your "industry standard method" fails. 



TORQUE:
In the aircraft maintenance industry the FAA often desires a torque value. This works fine until you use a fitting that is out of spec and bottoms out in the boss before reaching torque; Or the fitting that still leaks even though you have applied the proper torque; Or you reach the specified torque and the fitting is pointing in the wrong direction. Torque is not always practical with NPT or ANPT fittings because of the wide differences in friction (material, pipe dope, Teflon tape). Torque will sometimes get you in trouble; understand its weakness and use other quality assurance methods along with torque. 



FEEL:
Most screwed piping is tightened until it feels "right" and the fitting is pointing in the desired direction. What the experienced mechanic is often "feeling" is how the fitting is getting tight. Screw it into until it starts to seat. Then up the force a little by yanking. If each yank gives less movement, you probably have a sound joint. If the movement stops suddenly, you have probably bottomed out. The experienced plumber knows when to stop before he damages the fitting or boss. Caution is advised, tapered pipe fittings into an aluminum boss as excessive torque can crack the boss. This is especially true when using Teflon tape because the low friction of Teflon makes it easy to over-tighten.



NUMBER OF ROTATIONS:
Included in the standards for NPT and ANPT are engagement length, both straight and wrenched. For example, a 1/4 inch tapered pipe fitting should screw in 4.1 threads until finger tight (hand tight engagement), and 3 threads for wrench makeup. One problem is the wide variance in quality of the fittings and threads. Few 1/4 inch fittings screw in 4.1 threads before they reach finger tight. As a general guideline, after hand-tight engagement, tighten 2-3 full turns for sizes up to 1 inches for NPT fittings. You should have between 3.5 and 6 engaged threads. Any number outside of this range may indicate either under or over tightening of the joint or out of tolerance threads.



ASSEMBLY PROBLEMS:
Perhaps the most common fault a beginner makes is cross-threading the members and not realizing it. The male thread fitting needs to be aligned with the axis of the tapped hole. Rotation force should gradually increase with tightening.
User avatar
Lance Murray
5 Diamonds Member
5 Diamonds Member
Posts: 1163
Joined: Tue Jul 06, 2010 11:25 pm
First Name: Lance
Aircraft Type: DA40
Airports:
Has thanked: 7 times
Been thanked: 118 times

Re: Torque for the oil temp probe

Post by Lance Murray »

The short answer is between 2 and 3 turns from finger tight. This is from the Parker Hannifin Catalog 4300 Port End Assembly, page S7.
User avatar
astaib
5 Diamonds Member
5 Diamonds Member
Posts: 616
Joined: Mon Feb 26, 2018 9:00 pm
First Name: Arnaud
Aircraft Type: DA40
Aircraft Registration: FGNJX
Airports: LFPX
Has thanked: 244 times
Been thanked: 51 times

Re: Torque for the oil temp probe

Post by astaib »

Thanks and very interesting
Arnaud
DA40 Star 180 / 40.026 / 2001
Wingtip, landing and taxing LED (Whelen)
Skitube
GNS430 NON-WAAS
Steam gauges
Non certified ADS-b
User avatar
Thomas
4 Diamonds Member
4 Diamonds Member
Posts: 229
Joined: Tue Oct 19, 2010 6:20 pm
First Name: Thomas
Aircraft Type: DA40
Aircraft Registration: D-ENMA 40.337
Airports: LSZC BUOCHS SWITZERLAND
Has thanked: 91 times
Been thanked: 62 times

Re: Torque for the oil temp probe

Post by Thomas »

Arnaud
Lance brought it to the point:
"" FEEL: Most screwed piping is tightened until it feels "right" and the fitting is pointing in the desired direction""

Salutations Thomas - 35 years SWISSAIR mécanicien d'avion -
Thomas Bienz DA40-180 40.337 D-ENMA (sold 08/2022)
Home Airport LSZC Buochs Switzerland
Post Reply